GTX 1050 Ti Drivers, Black Screen After Driver Install, Code 43, Not Detected, Wrong Resolution, and No Signal Problems

GTX 1050 Ti Drivers, Black Screen After Driver Install, Code 43, Not Detected, Wrong Resolution, and No Signal Problems

A GTX 1050 Ti driver problem usually appears in one of two ways: Windows can still boot but the card has a driver error, or the system loses display as soon as the NVIDIA driver takes over from the basic display driver. 

Users reported blank screens halfway through driver installation, black screen after reboot, Windows loading followed by no signal, Code 43 in Device Manager, the card missing from Device Manager, fans spinning but no GPU detection, and resolution being locked at 800x600 after recovery attempts.

Problem: GTX 1050 Ti screen goes blank halfway through driver installation

What users observed: A user installing GTX 1050 Ti drivers on Windows 10 reported that the driver install reached roughly halfway, then the display went blank and the computer became unusable. After rebooting, Windows reached the loading screen and then went blank again. The user had already tried GeForce Experience, manual NVIDIA driver downloads, and several System Restore attempts.

What was tried: Users tried driver installation through GeForce Experience, manual NVIDIA packages, repeated System Restore, rebooting after the failed install, and returning to the pre-driver state. The case stayed close to black screen after GPU driver install, driver installed but display still not working, and wrong resolution after driver install, not a normal monitor cable issue.

How this played out: The repair path was to break the failed NVIDIA driver loop before trying another install. Users booted into Safe Mode, removed the broken NVIDIA driver state with a clean uninstall or DDU-style cleanup, restarted with the basic display driver, then installed a stable GTX 1050 Ti driver package instead of repeatedly installing over the failed one. When the same driver branch kept triggering the blank screen, users moved to an older NVIDIA driver and checked motherboard/Windows compatibility before testing again.

Problem: GTX 1050 Ti works before driver update, then BIOS shows but Windows goes black

What users observed: A user installed a new GTX 1050 Ti and had display output until the NVIDIA driver update. During or after installation, the screen went black and the TV reported no signal. The system still appeared to load BIOS, but Windows display output failed afterward.

What was tried: Users waited after the black screen, rebooted, checked whether BIOS still appeared, tested display output before and after Windows loading, and looked at the driver update as the change that broke the working display.

How this played out: The fix path was Windows driver cleanup rather than replacing the monitor first. Users used Safe Mode, removed the NVIDIA driver, booted with the basic display adapter, then installed a different stable driver version. If BIOS appeared but Windows did not, users treated the card as capable of basic output and repaired the Windows driver handoff. This is the same split used in GPU driver installed but display still not working cases.

Problem: GTX 1050 Ti black screen appears only after a specific NVIDIA driver version

What users observed: A GTX 1050 Ti user reported black screen at boot after installing NVIDIA driver 390.65. Another user with the same driver branch was advised to try an older driver, then later noted that older drivers also failed and that the motherboard itself may not have proper Windows 10 support.

What was tried: Users rolled back to older NVIDIA drivers, compared driver versions, checked whether the same black screen appeared with multiple releases, and looked at motherboard support for the installed Windows version.

How this played out: The repair path was driver version testing plus platform compatibility. Users removed the failed driver, tested an older known-stable driver, and checked whether the motherboard/BIOS supported the operating system well enough for the GTX 1050 Ti driver to initialize. When several NVIDIA versions failed the same way, the focus moved from one bad driver file to motherboard BIOS, chipset, Windows version, and legacy platform compatibility.

Problem: GTX 1050 Ti Code 43 appears in Device Manager

What users observed: A laptop user with a GTX 1050 Ti saw Device Manager report that Windows had stopped the device because it had reported problems, shown as Code 43. The user tried downloading the latest driver, but after restart the driver still did not seem to install correctly.

What was tried: Users installed the latest GTX 1050 Ti driver, restarted after the installer requested it, checked Device Manager again, and saw the card remain in a failed state. The case stayed close to GPU Code 43, NVIDIA driver installed but not working, and Windows driver missing behavior.

How this played out: The repair path was clean driver removal and correct driver source. Users removed the broken NVIDIA driver state, restarted, installed the laptop/OEM-compatible GTX 1050 Ti package where relevant, and checked chipset/BIOS updates if the card stayed in Code 43. For laptop GTX 1050 Ti cases, users avoided assuming that a desktop driver package alone would fix the device when the system needed the vendor-tuned graphics path.

Problem: GTX 1050 Ti is not detected after a power outage

What users observed: A user with a Gigabyte GTX 1050 Ti reported that the power went out while the PC was on. After that, the GPU was not detected in CPU-Z or BIOS. The user also tested the card in another PC, where it still was not detected.

What was tried: Users checked the card in the original PC, checked detection in BIOS and CPU-Z, moved the card to another PC, and compared whether the issue followed the GPU.

How this played out: The fix path was hardware isolation. Since the card was not detected in another PC either, users treated it as a GPU-level failure rather than a Windows driver, motherboard, BIOS, or power-supply setting. The practical result was to stop reinstalling drivers and verify the card with known-good hardware; if it remained absent in another system, replacement or repair of the GPU became the working path.

Problem: GTX 1050 Ti not showing in Device Manager even though fans spin

What users observed: Users reported GTX 1050 Ti cards where the fan spun or the card appeared powered, but Windows did not show the GPU in Device Manager. In one case, a second monitor shut off and the system no longer saw the graphics card after a reboot. The user checked seating and confirmed the card appeared to receive power.

What was tried: Users reseated the graphics card, checked whether the fans ran, checked Device Manager, tested monitor output, and looked for the card after reboot.

How this played out: The repair path was detection before driver installation. Users reseated the card, checked PCIe slot seating, tested another slot or PC where possible, cleared CMOS, checked BIOS display settings, and only installed drivers after Windows or BIOS could see the card. A spinning fan did not prove that the PCIe device had enumerated correctly.

Problem: GTX 1050 Ti driver installs but resolution stays low

What users observed: Some users recovered from black screen only to find Windows stuck at a low resolution, often with limited display options. This can happen when Windows is using a basic driver, when the NVIDIA driver did not attach correctly, or when the monitor/adapter path is not being read properly.

What was tried: Users checked Display Settings, Device Manager, NVIDIA driver state, monitor cables, adapter type, and whether the card appeared under Display adapters.

How this played out: The fix path was to confirm whether Windows was using the NVIDIA driver or a fallback adapter. Users removed the failed driver, reinstalled the GTX 1050 Ti package, checked Device Manager for NVIDIA status, and changed cables or ports if the monitor identity was not being read correctly. The problem belonged with wrong resolution, not with the monitor panel alone.

Problem: GTX 1050 Ti is installed but Windows uses Microsoft Basic Display Adapter

What users observed: Windows can show display output while still not using the NVIDIA driver. In this state, resolution options are limited, performance is poor, and games cannot use the GTX 1050 Ti properly.

What was tried: Users checked Device Manager, ran the NVIDIA installer, removed failed drivers, rebooted, and checked whether the card appeared as NVIDIA instead of a basic adapter.

How this played out: The fix was to attach the correct NVIDIA driver to the detected card. Users cleaned the failed driver state, rebooted, installed the GTX 1050 Ti driver, and confirmed the card name appeared under Display adapters. If the NVIDIA driver triggered black screen again, users rolled back to a stable earlier driver.